











The market share ofair source heat pumps is increasing. However, because it is a new type of heating equipment, many consumers are not clear about the installation precautions, which leads to the failure of the effect or various problems. Today, the main problem is to introduce the installation of an air source heat pump system and some precautions, so that everyone makes fewer mistakes.
Here is the content list:
Installation Steps
Water pipe connection
Precautions
This article focuses on analyzing the installation precautions of the home machine. By looking up relevant information, we can see that the installation of the air source heat pump heating system can be roughly divided into the following steps:
1. Before installing the host, it is necessary to survey the installation site, select and determine the installation location of the host.
2. Make the foundation of the host equipment. If the installation location is determined to be on the ground, cement can be used. The thickness of the cement is about 15cm~20cm.
3. Place the main engine and adjust the position of the unit to ensure the stable placement of the main engine.
4. The connection to the water system is mainly the connection of the water pump, valve body, filter, and other components between the host and the water tank.
5. Connect the circuit system, mainly to connect the power cord, water pump, solenoid valve, water temperature sensor, pressure switch, etc. according to the wiring diagram requirements.
6. Waterway pressure test, check whether there is water leakage in the pipeline connection.
7. Test the operation of the machine to check various parameters of the system.
8. Pipe heat preservation, such as using rubber and plastic heat preservation materials to heat the waterway system.
There are also some differences in the diameter of the water pipes of different types of air source heat pumps. When installing the water pipes of the air source heat pump, you need to pay attention to selecting the appropriate water pipes according to the specific model. Then connect the water pipe with other accessories and valves of the heat pump. When installing, you need to pay special attention not to let other debris enter the pipeline system. When connecting the water pipe, you can use a pipe clamp to operate, so that the water pipe can be firmly fixed.
Mastering the installation steps only masters the most basic installation knowledge. What really determines the quality of the installation is the many installation details. Every step of the installation has "rules" to be followed, which also requires the installer to master it firmly. There are many "rules" for the installation of air-source heat pump hosts. If the installer understands it, it will be of great benefit to improving the quality of the installation.
1. The survey work before installation is necessary. It is very necessary to survey the installation site before installing the host.
2. The host has high requirements for the installation space environment, and installation at different locations has different requirements. The air source heat pump host can be installed on the ground, on the roof, or on the wall. If it is installed on the ground, or on a wall, in order to ensure that the heat absorption and heat dissipation of the heat exchanger of the host is not hindered, the distance between the host and the surrounding walls or other obstructions should not be too small. In addition, the equipment foundation should be well prepared; The equipment should be installed on the ground, Use expansion bolts to fix it; If it is installed on the roof, the load-bearing capacity of the roof must be considered. The roof that does not meet the load-bearing requirements is strictly not allowed to be installed. If it can be installed on the roof, pay attention to the direction of the air source heat pump. The wind direction is best to install downwind so that the heat exchange effect of the host will be better.
3. It is very important to lay a good "foundation". The foundation of the equipment must be firm and strong. On this basis, the host must be placed and adjusted smoothly, ensure that it is installed upright, and fixed with expansion bolts.
4. Take measures such as rain and snow protection for the equipment. In the actual installation, it is also necessary to consider the drainage of the host equipment, rain and snow protection, lightning protection, maintenance space, and other issues. If these details are not considered in place, they will directly affect the air. The heating effect and service life of the source heat pump heating system.
It is the responsibility of each manufacturer to produce an industrial air source heat pump that meets the standards, so as to ensure the safety of the use of air-source heat pump and the healthy development of the air source heat pump market. MICOE many tests on air-source heat pumps before they leave the factory, and the quality qualification rate is guaranteed. If you are in the air source heat pump business, you can consider our cost-effective products.
An All-in-one heat pump is a heat pump that has three functions: Providing hot water , dehumidifying air in the swimming pool, and indoor air conditioning. It also has the function of fresh air exhaust and heat recovery.
Here is the content list:
What is the integrated dehumidification all-in-one heat pump air conditioning refrigeration function?
What is the heat recovery function of the all-in-one dehumidification heat pump?
What is an all-set dehumidification heat pump integrated heat pump air system?
The use of condensers depends on the weather conditions and the number of people in the pool. In low-temperature areas, the air does not need to be cooled in summer can not choose a condenser; in the south of the need for indoor air-conditioning cooling areas, an all-in-one heat pump is best to configure condenser, instead of air-conditioning. In summer, when the indoor air is overheated and the air conditioning and cooling function is needed, the outdoor condenser will start the cooling function. Outdoor condenser and air conditioning outdoor unit principle is the same, mainly to the excess heat out of the outdoor. Outdoor condenser, generally air-cooled radiator, like air-conditioning outdoor unit, to go to the refrigerant copper tube connection. But if the all-in-one heat pump is too far away from the mainframe, you can also use the cooling tower of the air conditioning, go to the water-cooling mode, the cold water into the mainframe refrigeration.
All-in-one dehumidification heat pump is the principle of air source heat pump, so the device also absorbs heat from the air as a source of heat (including heat from indoor pool water, which British studies have found accounts for 90% of the heat released by pool water), that is, it absorbs the heat from the indoor air, so the heat from the indoor air is not wasted (especially the heated air in winter is not wasted outside), but is absorbed by the equipment, reheat the indoor pool water and the indoor air. Fully Save Energy and operating costs, and according to the requirements in the exhaust system installed exhaust heat recovery device, so that the heat discharged to the outdoor air is almost fully recovered and reused. Thereby reducing heat loss, energy-saving, and emission reduction, and protecting the environment.
Reasonable air distribution can make indoor air temperature and humidity uniform, avoid condensation phenomena, so the design of the air duct system is crucial. All-in-one heat pump air duct organization design, the distribution of air supply can use one or more pipes, airflow direction down or direction prone to condensation walls, windows, etc. Return Air may be distributed using a pipe or branch with the return air outlet downward. Air Duct Design must ensure that there is no short circuit between supply air and return air otherwise it will exceed the high humidity layer and airbag. Fresh air outlet and vent distance can not be too close otherwise all-in-one heat pump will cause part of the ventilation directly into the fresh air system. It has been proved by many years of engineering practice that the diagonal installation of the air supply outlet and the air return outlet can make the equipment work most effectively in the indoor swimming pool. When the air duct is installed, the air supply outlet, the return air outlet, and the fresh air outlet must be installed with the air volume regulating valve. Rational selection of air volume proportion in seasonal climate change. Electric fire-proof air valves should be installed in the air supply port and connected with the fire control system. The air supply outlet, the return air outlet, the exhaust air outlet should install the muffler, reduces the noise.
MICOE Group ( stock code 603366 ) as China biggest supplier of solar water heater and hot water system, is a high-tech company which specializing in researching, manufacturing and marketing of renewable products. The business scope of the company involves solar water heater, heat pump water heater; water purifier; water tank and the heat pump-solar energy composite application etc, which can meet the different demands from industrial, commercial and residential application. With a full range of heat pumps and heat pump components, MICOE has built domestic heat pump production line, commercial heat pump production line, water tank production line, controller production line, metal cabinet production line and other industrial production lines. The production capacity and automation degree is in the leading position of heat pump industry.
If you want to learn more about the all-in-one dehumidification heat pump, read this article.
The snow-capped mountains and the glaciers of tens of thousands of years ago make you feel like stepping into the end of the world. Here is the "world's highest city" -- Pali Town, Yadong County, Shigatse City. The so-called "lonely at the top", the average altitude is more than 4,300 meters, so that people here with a lifetime of cold wind companion. Micoe, as a leading brand of air energy, has come forward to provide air heating services for pari Town primary school in Yadong County, Xigaze city, with excellent product performance and perfect after-sales service of its air energy units. It has set up another model project of clean heating in high altitude and extremely cold areas.
Leap into modern times, air can become a new way of heating the plateau
It is understood that Pagri Town (Pagri Zhen) is located in the middle of Yadong County, Xizang Province, known as the "world's first high city", about 4300 meters above sea level, is a cold and arid plateau climate area, although the sunshine time is long, but the annual minimum temperature as low as minus 20℃, winter as long as 6 months, even to June, there is no melting snow under the eaves. Under such harsh natural conditions, local residents still use relatively primitive wood and cow dung fire to keep warm. However, in the primitive classrooms, even basic fire heating is difficult to do, and young students can only "hard resistance", often shivering with cold, learning conditions are very difficult.
After the completion of the new school building, in order to create a warm campus environment for students and make the plateau no longer "cold and high", the school leaders decided to purchase a more advanced and efficient heating system for the school after consultation. After many investigations, Micoe's air energy heating scheme has been favored by the school.
Micoe comprehensive consideration of heating comfort, convenience, energy-saving effect and cost control and other factors, through detailed and thorough heat load calculation, the use of CSA system for Yadong County Pali Town primary school tailored air source heating solutions. The construction area of the comprehensive building of Pali Town Primary School in Yadong County is about 1460.08m ², and the heating area is about 909m². The building area is about 1978.32m ², and the heating area is about 1177m². Three ultra-low temperature and high efficiency air source heat pump units are used to run in parallel in the complex building and teaching building respectively (air-cooled heat pump unit and water pump room are located outdoors), and ground low temperature radiation heating is used in the indoor building. This scheme can fully meet the requirement that the heat produced by the air source equipment is still above 701KW in the low temperature environment of -12℃ outdoor environment in winter, and truly realize the function of safe and stable heating in the low temperature environment.
Installation service across the snowy plateau
In recent years, air source heat pump, widely used in the "coal to electricity" project in northern China, has provided a new idea for clean heating in Tibet. However, it is a very difficult challenge to carry out heating engineering transformation in plateau area. The climate of plateau and high altitude area is complex and changeable, easy to hypoxia, low temperature, strong ultraviolet ray, heavy sand, etc., which greatly increases the difficulty and quantity of project construction.
"Pali Town Primary School is located in a remote area. It takes one week for air energy products to travel from Shunde, Guangdong province to Lhasa, Tibet via Sichuan-Tibet Line, and it takes eight hours to drive from Lhasa to Pali Town. In winter, the temperature is as low as minus 10℃ ~ 20℃, which makes it difficult for many people to adapt and easy to lack of oxygen. Micoe Took part in the central heating project renovation of Pari Town Primary School.
In recent years, air source heat pump, widely used in the "coal to electricity" project in northern China, has provided a new idea for clean heating in Tibet. However, it is a very difficult challenge to carry out heating engineering transformation in plateau area. The climate of plateau and high altitude area is complex and changeable, easy to hypoxia, low temperature, strong ultraviolet ray, heavy sand, etc., which greatly increases the difficulty and quantity of project construction.
"Pali Town Primary School is located in a remote area. It takes one week for air energy products to travel from Shunde, Guangdong province to Lhasa, Tibet via Sichuan-Tibet Line, and it takes eight hours to drive from Lhasa to Pali Town. In winter, the temperature is as low as minus 10℃ ~ 20℃, which makes it difficult for many people to adapt and easy to lack of oxygen. Micoe Took part in the central heating project renovation of Pari Town Primary School.
Heating Pari Town primary school, he recalls, was first a matter of unit transport. In March 2022, Micoe Pali Town Primary School clean heating project came into the construction, the road condition was particularly bad, the car is prone to break down on the way. As the altitude continues to rise, altitude sickness and road closures caused by heavy snow occur one after another, and mobile phone signal is poor. Living in a sparsely populated Tibetan area, I have to find my own way to solve the problem. For example, in some places the carts could not reach, so they were transported separately by small cars.
Customized solutions, Micoe warms every hand
In addition, the installation process is extremely difficult. Because the unstable voltage of the school is easy to power off during the construction process, the installation team must prepare a diesel generator in advance. Once the power is off, it can continue to work by itself. Due to the lack of oxygen in the plateau, the working intensity can not be too high, and the labor efficiency is lower than that in the plain area. March to April, just belongs to the dry and windy season, sand and long duration, put forward a severe test to the construction. Under the environment of minus 10℃ or so, if the construction only wears a layer of gloves, it is easy to be frozen by hot-dip galvanized steel pipe, and sometimes remove the skin of the hands. Only two or three layers of gloves can work, greatly reducing the sensitivity of the fingers.
Despite the difficulties, Micoe managed to complete the project smoothly. In the scoring standard of the central heating project of Pari Town Primary School, Micoe got high marks in both the perfection and implementability of the transportation guarantee scheme and the completion of the detailed work schedule of the supplier, and was unanimously recognized by the project party and leaders.
Heating Pari Town primary school, he recalls, was first a matter of unit transport. In March 2022, Micoe Pali Town Primary School clean heating project came into the construction, the road condition was particularly bad, the car is prone to break down on the way. As the altitude continues to rise, altitude sickness and road closures caused by heavy snow occur one after another, and mobile phone signal is poor. Living in a sparsely populated Tibetan area, I have to find my own way to solve the problem. For example, in some places the carts could not reach, so they were transported separately by small cars.
In addition, the installation process is extremely difficult. Because the unstable voltage of the school is easy to power off during the construction process, the installation team must prepare a diesel generator in advance. Once the power is off, it can continue to work by itself. Due to the lack of oxygen in the plateau, the working intensity can not be too high, and the labor efficiency is lower than that in the plain area. March to April, just belongs to the dry and windy season, sand and long duration, put forward a severe test to the construction. Under the environment of minus 10℃ or so, if the construction only wears a layer of gloves, it is easy to be frozen by hot-dip galvanized steel pipe, and sometimes remove the skin of the hands. Only two or three layers of gloves can work, greatly reducing the sensitivity of the fingers.
Despite the difficulties, Micoe managed to complete the project smoothly. In the scoring standard of the central heating project of Pari Town Primary School, Micoe got high marks in both the perfection and implementability of the transportation guarantee scheme and the completion of the detailed work schedule of the supplier, and was unanimously recognized by the project party and leaders.
28th September 2013, award ceremony of “World Executive Summit 2013 and Asia’s 500 Most Influential Brands” held in Hong Kong, during the award ceremony, Micoe pass through The Asia’s 500 Most Influential Brands’ strict selection and Auditing, brand strength and potential of development has been recognized, becoming the first “Asia’s 500 Most Influential Brands” in the China’s new energy industry. Mr. Robert Mundell, the chairman of World Executive Group, professor of Columbia University, winner of 1999 Nobel Prize in Economics and Mr. Ravi Dhar, senior professor of Yale University, director of Yale user monitoring center pass the Certificate to Micoe, also Samsung, Toyota, Industrial & Commercial Bank of China, China State Grid Corporation, CCTV and etc, has be rewarded along with Micoe. There are 188 brands from Chinese Mainland in the list.
Professor Robert Mundell delivered a speech and stated the concept and meaning about “The Asia’s 500 Most Influential Brands” corporate rankings, he said, the rapid development of Chinese enterprises is worth of being praised and respected by the whole world due to making great contributions to the global and Asia’s economy, especially in the field of new energy.
“The Asia’s 500 Most Influential Brands” is a authoritative list which measuring multi-fields large enterprises’ size, influence and strength, also reflect the state of the world economy, it is very authoritative. May 2012, Solar East—Micoe Listed in Shanghai A stock (603366); April 2013, the State Statistical Bureau authority released: In year 2012, all-glassvacuum tube solar water heater made by Micoe sales volume is the largest in the same products in China; This time, again, Micoe has become the first “Asia’s 500 Most Influential Brands” in the China’s new energy industry.
Since the establishment of Micoe, specialized in engaging market-oriented commercial practice in Chinese new energy industry, and successfully explored a replicable promotion road about new energy. For 13 years, based on the whole industry chain manufacturing platform which scale is the largest and quality is the highest in solar industry, continually carrying on technology innovation and business model research, leading and pushing forward the development of solar thermal utilization industry of Chinese new energy, meanwhile the favorable corporate responsibility has been winned widespread praises from the social publics. In 2013, Micoe has put forward industrial strategy called “large solar thermal”, which not only clearly draws the outline of technical roadmap of solar thermal utilization industry, but depicts a brand new and large blue ocean market of solar thermal collector industry.
The related experts said, just these five advantages that establish today’s market position of Micoe, and which is the secret that why Micoe has the ability to win “The Asia’s 500 Most Influential Brands”.
(Professor Robert Mundell, who is the chairman of World Executive Group、professor at Colombia University in United States、winner of the Nobel prize in Economics in 1999, made speeches)
(Professor Robert Mundell & Professor Ravi Dhar(middle) jointly presented award for Mioce)
Certificate